KINGSPAN K18 PDF

Kooltherm K18 Insulated Plasterboard is a super high performance insulated dry- lining plasterboard suitable for mechanical fixing. Buy mm Kingspan Kooltherm K18 Insulated Plasterboard, a premium performance fibre-free rigid thermoset phenolic insulation core bonded to mm. Kingspan Kooltherm K18 Insulated Plasterboard is a premium performance insulation, with a fibre-free rigid thermoset phenolic insulation core with mm .

Author: Meztibar Mogore
Country: Saint Kitts and Nevis
Language: English (Spanish)
Genre: Business
Published (Last): 9 July 2014
Pages: 60
PDF File Size: 19.2 Mb
ePub File Size: 1.20 Mb
ISBN: 218-7-23654-584-1
Downloads: 78170
Price: Free* [*Free Regsitration Required]
Uploader: Vit

Celotex FI range, for underfloor heating. Celotex PL range, Plasterboard Backed. Jab Floor 70 Expanded Polystyrene.

Your basket is empty. Visit the store to add products to your basket. Write an online review and share your thoughts with other shoppers! Premium performance rigid phenolic insulation — thermal conductivity as low as 0.

You might also consider Celotex PL range which is a cheaper product with similar performance spec. Used when fixing to solid wall constructions that are susceptible to rain water penetration. Kooltherm K18 combines insulation, dry—lining and vapour control in one board. This product is a mechanical fix product and as kngspan is most easily erected using battens.

K ingspan Kooltherm K18 Performance insulated phenolic plasterboard. Available in in the standard size of mm wide by mm long, and in the following thicknesses We can also source the following sizes for larger orders However, short lead times may apply.

Determination of compression behaviour. Methods 7 to kingdpan.

Kooltherm K18 Insulated Plasterboard | Kingspan | Australia

It should, therefore, not be used to isolate dampness nor be used in continuously damp or humid conditions. Jingspan durability kinhspan on the supporting structure and the conditions of its use. The insulation core is resistant to short—term contact with petrol and with most dilute acids, alkalis and mineral oils. However, it is recommended that any spills be cleaned off fully before the boards are installed.

Ensure that safe methods of cleaning are used, as recommended by the suppliers of the spilt liquid. The insulation core is not resistant to some solvent—based adhesive systems, particularly those containing methyl ethyl ketone. Adhesives containing such solvents should not be used in association with this product. Damaged boards or boards that have been in contact with harsh solvents or acids should not be used.

Test – BS —6: Method of test for fire propagation for products. Result – Fire propagation kingspxn of Fire tests kings;an building performance 1 not exceeding 12 and sub Index i1 not exceeding 6 for rigid phenolic insulation core. Test – BS —7: Method of test to determine the classification of the surface spread of flame of products. The ceiling lining should be in position before wall lining commences.

  ELECTROTECHNIQUE WILDI PDF

Kingspan Kooltherm K18 Insulated Plasterboard – 12.5mm

Wall mounted fittings such as electrical sockets should be fitted so as to take into account the additional wall thickness.

On existing constructions all surfaces should be kingsan and free of loose or flaking materials. Wallpaper should be stripped and surface mounted fittings removed. Fixing should employ the same method as is used for the plain wall areas.

Care should be taken to ensure that the cavity in cavity wall constructions is not bridged by the board or fixing medium in such a manner that would allow the passage of water through to the inner leaf.

Where adhesives are employed, soffit boards and boards at window heads should be temporarily supported. This method may be used on timber frame constructions or on any dry masonry walls that will support and retain the battens and associated fixings. The timbers should run vertically and be wide enough to offer a minimum 20 mm support to all four edges of the board. Drywall screws or, alternatively, galvanised clout nails, long enough to allow a minimum 25 mm penetration of the timber, should be placed at mm centres and not less than 10 mm from the edges of the board.

They should be driven straight with the heads embedded just below the surface of the board. Timbers should be treated where appropriate.

Kingspan K18 Kooltherm Phenolic Plasterboard for Mechanical Fixing

The frame should be set vertically at a maximum of mm centres to coincide with board joints and midpoint of board. Short lengths of metal framing should be fixed horizontally between the vertical pieces at skirting level, at the midpoint of the board and just below the ceiling or soffit level. Provision for horizontal services behind the board can be made by the use of two pieces of metal framing set no more than mm apart.

Screws should not be sited less than 10 mm from the edges of the board. The screws should be driven straight until the heads are slightly below the paper surface of the plasterboard facing. Care should be taken not to overdrive screws. Installation is similar to that of standard plasterboard. Boards must always be placed with the long edge running across the joists, rafters or battens and all edges must be supported.

  GANESHA ASHTOTHRAM IN MALAYALAM PDF

Timbers must offer a minimum 20 mm support to all four edges of the board. This will necessitate the use of noggings placed between the joists to coincide with the long edges of the board.

These must be long enough to allow a minimum 25 mm penetration of the supporting timber, and be placed not less than 10 mm from the edges of the board and be spaced at mm intervals along all supporting timbers.

The wall should be sound, dry and level as surface irregularities may impede fixing of the board. The board should be fully restrained using mechanical fixings. Fixings should not overlap board edges.

Tapered edged boards allow the employment of standard dry—lining techniques. A plaster skim finish can also be applied to the boards. Cutting should be carried out either by using a fine toothed saw, or by scoring with a sharp knife, snapping the board over a straight edge and then cutting the facing on the other side. Ensure accurate kijgspan to achieve close butting joints and continuity of insulation.

Search Product Enter keyword. Shopping Your basket 1k8 empty. Customer Review Write kinfspan online review and share your thoughts with other shoppers! Sorry, no review found, please be first one to review it. Kingspan K18 Boards See it? Product Description Used when fixing to solid wall constructions that are susceptible to rain water penetration.

Benefits Premium performance rigid phenolic insulation — thermal conductivity as low as 0. Kooltherm K18 combines insulation, dry—lining and vapour control in one board Kingspan K18 Board Sizes and Values Available in in the standard size of mm wide by mm long, and in the following thicknesses Method of test for fire propagation for products Result – Fire propagation index of Fire tests on building performance 1 not exceeding 12 and iingspan Index i1 not exceeding 6 for rigid phenolic insulation core Test – BS —7: Method of test to determine the classification of the surface spread of flame of products Result – Class 1 rating Test – BS —1: Finishing Tapered edged boards allow the employment of standard dry—lining techniques.

Insualted Kibgspan Installation Customer Review Write an online review and share your thoughts with other shoppers!