14mz, Instruction manual • Read online or download PDF • Futaba 14MZ User Manual. Get Futaba 14MZ Manual. Get all Futaba manuals! 14MZ. 14 CHANNEL RADIO CONTROL SYSTEM. PCMG3/PCM/FM selectable. INSTRUCTION. Compact Flash (CF) Card Handling Instructions Follow these precautions when handling the CF card included in your 14MZ transmitter. DO NOT allow the.

Author: Arashiktilar Dajar
Country: Senegal
Language: English (Spanish)
Genre: Science
Published (Last): 25 May 2007
Pages: 41
PDF File Size: 11.40 Mb
ePub File Size: 12.30 Mb
ISBN: 931-6-65783-875-6
Downloads: 63772
Price: Free* [*Free Regsitration Required]
Uploader: Brataxe

But if more than four hours pass after shutting down the power, the power supply will completely shut down the internal circuit. You can now open the cover in the direction of the arrow.

The data of up to 30 models can be saved to the transmitter. This product is suitable for model airplane, surface or 50 MHz license required use, if on the correct frequency. After activating the throttle cut function and selecting the switch, adjust the throttle position so that the carburetor becomes full open. This time can be set by ten-second steps. Music playback The T14MZ transmitter can play back the “.

Frequency Frequency Band frequency setting, modulation mode setting, receiver ID code setting.

Futaba 14MZ User Manual | pages

Comments to this Manuals Your Name. Touch the button of the curve type you want to use. When transmitter power switch turned on No. Frequency ” button if you need to change the frequency.

Throttle Hold This function sets the throttle cut position at auto rotation dive.

The RBRC program provides a convenient alternative to placing used nickel-cadmium batteries into the trash or municipal waste system, which is illegal in most areas. Tell us about it.


You shall only move the T14mzUtility. Reset Button How to change the frequency 1. Up to 3 rates can be set for each condition. Switch selection method The various functions used in the T14MZ can be selected by switch. If you kanual on the power switch again while the transmitter is still in the process of power shutdown, the data could be damaged.

Turn on the transmitter power and allow your transmitter to reach its home screen. Select the range of the frequency band of the module used. Before setting the model data, use the Model This section outlines the relationship between the Type function of the Linkage Menu to select the Detailed instructions for use are in the User’s Guide.

Operating instructions FUTABA 14MZ

Touch the Trim button to call the Trim setup screen. When another model type is selected thereafter, the AFR, program mixing, and other setting data are reset. 14mx it, continue to print. Disappearance of the cross hair cursor means the calibration has been completed.

Use your finger or included stylus pen to operate the touch screen. Do not 41mz Li-Ion cells to come in contact with moisture or water at any time. US only 72 or 50 MHz bands Modulation: Avoid mounting the switch where it can be covered by engine oil and dust.

Pitch to RUD mixing curve Normal Use the hovering system and set this curve to match take off and landing and vertical climb at a 14m speed. Servo connection by model type The T14MZ transmitter channels are automatically assigned for optimal combination according to the type selected with the Model Type function of the Linkage Menu.


You can listen to them through the built-in speaker or a headphone by the earphone plug. You can now open the cover in the direction of the arrow. Definitions of Symbols Pay special attention to safety where indicated by the following symbols.

It has a backlight and the screen is manufactured of a transflective construction which enables both indoor and outdoor visibility.

Idle down – Futaba 14MZ User Manual

Operation modes The manuwl modes when stick, trim lever or VR are selected are described below. There are two “start up” modes for your transmitter, see below: For safety reasons, the radio will be emmiting only after you push the confirmation button when turning on the power. Page Curve setting examples actually creating a curve, enter the data specified The curves shown below were created by using per the fuselage or the reference value. Lifting force can be increased at elevators up.

Airplane, general This function is used when you want to mix elevator operation with rudder operation. In this case, the same contents are input to the other conditions set in the group mode. Please be careful so that you don’t scratch the touch panel with something hard, such as metal and sand sticking on the surface. Prior approval of the appropriate government authorities may be required. Timer Timer setting and lap time display. If you continue pressing it, the manua, position starts to move faster.